![]() No matter what I then throw it via can-send I can't get a response back. compatible with Windows 2000, XP, VISTA, 7, 8 and 10 amc MacOS. USB 1.1 and USB 2.0 compatible, supported data transfer speed up to 1 Mbps. IP link then gives me: 6: slcan1: mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10 For connecting serial devices, such as modems, measuring devices, toys, service interfaces, telephone systems, etc., to a USB port. ![]() Like so: sudo slcand -o -s6 -t hw -S 3000000 /dev/ttyUSB2 Lsusb gives me: Bus 003 Device 002: ID 1a86:7523 QinHeng Electronics HL-340 USB-Serial adapter Changing the local hostname might make it unresolveable. systemd-hostnamed: Warning: nss-myhostname is not installed. can: broadcast manager protocol (rev 20120528 t) usb 3-3: ch341-uart converter now attached to ttyUSB1 Data transfer pin contains: TXD pin and RXD pin. In asynchronous serial interface mode, CH340 chip contains these pins: data transfer pin, MODEM liaison signal pin and assistant pin. The CH340 series chip can operate in 3 modes of USB to serial interface converter mode, USB to infrared converter mode and USB to. Copy link mihalski commented Jul 8, 2020. USB To RS232 DB9 Serial Port Converter Cable is an 80 cm cable with two heads of a 9 pin male DB9 connector and a USB v2.0 male, which converts RS232 port to USB port. 9 comments Closed Support for QinHeng Electronics HL-340 USB-Serial adapter (CH340) 1027.NOS is lowlevel can forbid USB device suspending. Support for QinHeng Electronics HL-340 USB-Serial adapter (CH340) 1027. ch341 3-3:1.0: ch341-uart converter detected CH340 automatically supports USB device suspending to save power consume. usb 3-3: New USB device strings: Mfr=0, Product=2, SerialNumber=0 The actual device Im using is a clone Arduino Nano device from amazon. Im using a Raspberry Pi 2 with Raspbian Wheezy installed. This may be some useful information: lsusb brings up this for the device: QinHeng Electronics HL-340 USB-Serial adapter. ![]() usb 3-3: New USB device found, idVendor=1a86, idProduct=7523 I cant figure out what Im doing wrong here, but I really need this driver to be installed. Ive uploaded OptiBoot to Atmega328 and then Ive set BLB1 to lock LPM and SPM in the boot section and Ive set the BOOTRST fuse to One. These project boards are often used in workshops, labs and areas when a Windows 7 machine may still be in use. ![]() Which use the CH340 chip : With one difference, Ive use SPI pin to program the MCU. The CH340 chip converts TTL (serial) to USB, this chip is used in programming/project boards, cables and many other applications. This is the canopen device I'm trying to get at and this is the adapter I'm usingÄmesg: usb 3-3: new full-speed USB device number 8 using xhci_hcd Ive started to build a Arduino Nano with CH340g using this schematic. 2) dmesg 11438.808672 usb 2-3: new full-speed USB device number 6 using. To communicate with the device, I need to know the device name (if any) What can I try to find it What I have tried: 1) lsusb Bus 002 Device 006: ID 1a86:7523 QinHeng Electronics HL-340 USB-Serial adapter. I'm trying to communicate with a serial to the can-bus adapter in 14.04 with can-utils My ESP8266 developers board communicates via a USB serial device.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |